Showing posts with label classic. Show all posts
Showing posts with label classic. Show all posts

1956 Ferguson Vaaljapie TE-F 20 #2

OPERATIONAL INSTRUCTIONS for the FERGUSON TE-F 20 Tractor (Vaaljapie) ....... WARNING Keep a new tractor on light work for fifty hours.


WARNING
Keep a tractor on light work for fifty hours.


Keep the fuel system, fuel storage and handling arrangements scrupulously clean. Do not tamper with the injector pump, governors or injectors. Drive slowly in difficult going. Do not carry anything on the implement. Keep all nuts and bolts tight. This precaution is a general practice with all good operators, who have found that it prolongs the life of the tractor by keeping all parts in perfect alignment. Use an adequate shield to protect the power take-off universal joints. Do not use the draw bar without the drawbar stays. Allow ten seconds to elapse before re-engaging starter if previous attempt at starting has failed.

IT IS HIGHLY DANGEROUS TO PULL ANYTHING FROM THE TOP LINK CONNECTION


YOU HAVE BEEN WARNED


WARNING AGAINST OVERLOADING 
The third gear should not be used with any implement which operates underneath the ground such as a plough, cultivator, etc.

The hydraulic system is designed to operate perfectly in first or second gear but it will not operate perfectly in third gear.

The third gear is too fast for normal implement use. Implements such as ploughs and cultivators, which operate underneath the ground, and which are liable to catch on obstructions, are not designed to stand stresses above 3 m.p.h. (5.6 k.p.h.). It is a fallacy to think that operating in third gear will save the tractor and save fuel for normal work. This gear for normal work would cause overloading, and overloading is disastrous to the life of a tractor.

The third gear is meant to be used for light work only and for implements which operate above the ground, such as a light roller.

A SIMPLE TEST OF OVERLOADING 
With the tractor in motion set the throttle lever about half way open. Then quickly flick the throttle fully open. If the tractor speeds up rapidly the engine is not overloaded—if slowly, the engine is overloaded. These remarks apply to any tractor. The overloading should be remedied at once to avoid serious damage.

When operating up a steep hill the above test might indicate overloading. This is not harmful as it is compensated for when coming downhill.

It is continuous overloading that must be avoided.

OPERATIONAL SECTION 
This section describes the principal tractor controls, how they are used and how the engine is started in varying climatic conditions.

Fig. I 

A. CLUTCH PEDAL.
B. FOOT REST.
C. GEAR SELECTOR LEVER.
D. PRE-HEATER CONTROL SWITCH.
L. FOOT REST
E. FUEL CUT-OFF CONTROL.
M. COMBINED BRAKE PEDAL
F. OIL PRESSURE GAUGE. WITH PARKING LATCH.
G. HAND THROTTLE LEVER.
N. HYDRAULIC CONTROL LEVER.
H. KIGASS INJECTOR PUMP.
J. AMMETER.
K. DECOMPRESSION LEVER— REAR.
0. STARTER SWITCH SAFETY BUTTON.

CONTROLS & INSTRUMENTS (Figs 1 & 2)

Gear Selector Lever
Lift lever for selection of reverse gear or for operation of electric starter in conjunction with safety button.

Pre-heater Control Switch
Use in conjunction with Kigass injector pump and hold out to operate.

Fuel Cut-off Control
Pull out to stop engine.

Excess Fuel Device
Press operating button before starting up (See Fig 11)

Oil Pressure Gauge
Normal pressure : 40-60 lb./sq.inch (2:8-4:2 kg./sq.cm)

Hand Throttle Control
Move clockwise to increase engine speed.

Kigass Injector Pump
Unscrew and pull out knob, then push in sharply to inject furl spray into the manifold. Screw knob in to secure.

Ammeter
Rate of charge depends on state of batteries.

Decompression Lever Three positions :-

UP - allowing full compression to all four cylinders.
INTERMEDIATE - located by ball catch - relieving compression from three cylinders.
DOWN - relieving compression from all four cylinders.

Combined Brake Pedal
Pressure on this pedal operates brakes on both rear wheels. Ratchet can be engaged for parking. Independent Brake Pedals Pressure on either pedal on appropriate wheel only, to assist reduction of turning circle.

Fig 2 

KEY TO FIG 2

A. ADJUSTABLE STOP
B. HYDRAULIC PUMP CONTROL LEVER
C. CONTROL LEVER QUADRANT
D. HYDRAULIC MECHANISM AND TRANSMISSION OIL DIPSTICK
E. STARTER SPRING LOADED SAFETY STOP
F. INDEPENDANT BRAKE PEDAL (R.H.)
G. BATTERY INSPECTION PLATE.

Hydraulic Control Lever
When hydraulic pump is in operation, rearward movement of lever raises linkage, forward movement allows it to drop under its own weight.

Starter Switch Safety Button
This must be pressed while gear selector lever is moved forward to operate electric starter. Automatic return when gear lever is moved back to neutral position.

COLD STARTING EQUIPMENT 
The object of this system is to provide pre-heating and priming of the inlet manifold and combustion chambers prior to starting in temperatures below 32ºF (0ºC). An atomised fuel spray is injected into the air inlet manifold by operating the Kigass injector pump located on the instrument panel. The spray impinges on to a heater coil screwed into the manifold, providing a warm fuel vapour to assist firing.

Fig 3 

The Kigass filter (see Fig 3) should regularly be dismantled by unscrewing lever type cap and the filter gauze removed and cleaned.

ENGINE STARTING PROCEDURE (Figs 1 and 4)

IMPORTANT 
Disengagement of the starter pinion is automatic. The gear lever must be returned to the neutral position as soon as the engine fires. If the engine fails to run after firing, do not immediately jab the starter into re-engagement. Always wait at least ten seconds if previous starting attempt has failed.

Before attempting to start the engine, ensure that:-
(a) There is sufficient fuel in the tank.

(b) That all fuel line cocks are open and cut-off control is in starting position.
(c) The clutch pedal is depressed.
(d) The brake is 'on' and the ratchet engaged.

Warm weather, above 50ºF (10ºC)

1. Ensure that the decompression lever is in 'up' position to give full compression for all four cylinders.
2. Depress the excess fuel device located on the injector pump.
3. Move the hand throttle lever to the half-open position.
4. Operate the starter.

Cool weather, 32ºF-50ºF (0ºC-10ºC) 

1. Ensure that the decompression lever is in the 'down' position to relieve compression from all four cylinders.
2. Depress the excess fuel device.
3. Move the hand throttle lever to the half-open position.
4. Operate the starter for two seconds, then, still allowing it to remain in operation, move the decompression lever to the intermediate position, giving pressure relief on three cylinders.
5. Immediately the engine fires, move the decompression lever up to 'full compression'.
6. As soon as all four cylinders have fired, return the gear lever to 'neutral' and set the hand throttle lever at just above 'idling' position to warm up the engine.

Cold weather, below 32ºF (0ºC) 

Warming up (before starting) 

1. Set the hand throttle lever in the half-open position.
2. Pull out fully the fuel cut-off control and lock in this position.
3. Set the decompression lever in the 'down' position to relieve compression from all four cylinders.
4. Hold out pre-heater control switch for 15 seconds to allow the coil to become hot, then, continuing to hold out the switch, give ONE full charge only with the Kigass injector pump, operating sharply to ensure that the spray is fine enough to be ignited.
5. Operate the starter for 10 seconds to allow the hot vapour to be drawn into the engine.
6. Release pre-heater control switch and disengage starter.

NOTE : If the batteries have become discharged, current should be conserved for starting by turning the engine by hand during the warming-up period. This is not difficult, as the engine is fully decompressed. Normally, an additional person is required to use the starting handle, but the procedure can, if necessary, be carried out by the driver alone if the heater coil switch is held out by means of a wedge. The wedge must be removed immediately after the warming-up cycle to avoid further drain on the batteries.

Fig 4 

KEY TO FIG 4

A. PRE-HEATER CONTROL SWITCH
B. THROTTLE LEVER
C. KIGASS INJECTOR PUMP
D. ANNETER
E. DECOMPRESSION LEVER REAR
F. FUEL CUT-OFF CONTROL
G. GEAR SELECTOR LEVER

7. Move the decompression lever up to the 'full compression' position.
8. Release the fuel cut-off control.
9. Depress the excess fuel device.
10. Give approximately HALF stroke with the Kigass injector pump.
11. Pull out pre-heater control switch.
12. Operate the starter for ten seconds.
13. As soon as the engine starts, release the heater switch, return the gear lever to 'neutral' position and set the hand throttle lever at just above 'idling' position to warm up engine.

NOTE: If the engine does not start within 10 seconds, do not continue the attempt to start, but five a further warming-up as previously described.

N.B. - The Kigass pump must be screwed back securely after use.

TO STOP THE ENGINE 
Pull the fuel cut-off control under left-hand side of instrument panel, shown in Fig 4. In cases of emergency only should engine be stopped by operating the decompression lever or by turning off any of the fuel taps.

BEFORE STARTING WORK 
Check that engine oil pressure is correct. Ensure that there is an ample fuel supply in the tank for the work in hand.




::
 

1956 Ferguson Vaaljapie TE-F 20 #1

HANDLING NOTES for the FERGUSON TE-F 20 Tractor (Vaaljapie) 


The Ferguson TE20 is an agricultural tractor designed by Harry Ferguson. By far his most successful design, it was manufactured from 1946 until 1956, and was commonly known as the Little Grey Fergie. It is light-weight but effective, and a popular collector's item for enthusiasts today. 

Harry Ferguson was born in Ireland in 1884 and at the age of 14 became an apprentice at a car and cycle shop in Belfast owned by his elder brother Joe. This was the beginning of his interest in all things mechanical, including aeroplanes.

He then established his own business selling various makes of cars, took an agency to sell Waterloo Boy model N tractors (the Overtime), and in 1917 the Irish government asked him to tour Ireland to help improve Ireland's tractors - the rest is now history.



HANDLING NOTES for the FERGUSON TE-F 20 Tractor (Vaaljapie)

The following notes have been compiled to assist you to obtain maximum service from your tractor by avoiding inadvertent damage.

CLUTCH OPERATION
Use the clutch only when selecting the gear ratio to be used or to engage or disengage P.T.O. drive. If the load on the engine is goo great for the gear in use, always stop and select a lower gear. Never slip the clutch in order to increase engine speed. Never attempt to change gear when the tractor is in motion. Avoid resting the left foot on the clutch pedal, as this may cause the clutch to slip.

POWER TAKE-OFF SHAFT
The shaft projects from the centre of the rear axle and is enclosed by a removable cap. The operating lever for the P.T.O. clutch is mounted in the left-hand inspection cover of the centre axle housing, as shown in Fig. 5. Movement of the lever towards the rear engages the drive. Engine clutch must be depressed to engage or disengage the P.T.O. drive. Do not run with the drive constantly engaged when the Power Take-Off or Hydraulic Mechanism is not being used.


HYDRAULIC LIFT
As the hydraulic pump is driven by the P.T.O. shaft, the latter must be engaged before the hydraulic system can operate. The hydraulic control lever is situated at the driver's right-hand, as shown in Fig. 2. Rear-ward movement of this lever raises the hydraulic linkage, forward movement releases the hydraulic pressure, allowing the implement to fall. When an implement is in work, the depth at which it operates is governed by the distance that the control lever is moved forward, and an adjustable stop, fitted to the control lever quadrant, ensures that the lever is moved to the same position each time the implement enters work.

The pump has external delivery points for use with implements which incorporate remote pressure operated hydraulic systems, such as the Ferguson High Lift Loader. Before removing plugs (see Fig 5), to connect up implement, make sure the pump is disengaged.

HYDRAULIC PRESSURE RELIEF VALVE
Avoid using the tractor hydraulic system in any way which causes the pressure relief valve, which is internal, to discharge continually. Although this will not actually damage the system, it may cause a slight reduction in the maximum operating pressure.

Where, on later tractors, the Relief Valve is fitted in the lift cover, it is constructed so that, when it opens, all the working parts are lubricated and submerged in the discharged oil, it is therefore desirable for the Relief Valve to be discharged at regular intervals. This can best be effected by an occasional short attempt to raise a load on the lower links greater than the system is capable of lifting.

The maximum recommended load for normal work on all tractors is 1000lbs (453.6kg) a the point of implement attachment on the lower links, and this figure should not otherwise e exceeded.
Warning : Adjustment and inspection of the Relief Valve must be strictly entrusted to an authorised service engineer; unskilled attention to this assembly may result in serious damage to the Hydraulic System.


KEY TO ANNOTATION
A. OPERATING LEVER - P.T.O. CLUTCH
B. DIPSTICK - TRANSMISSION OIL
C. HYDRAULIC SYSTEM RELIEF VALVE
D. GREASE NIPPLE - INDEPENDANT BRAKE SHAFT
E & F. HYDRAULIC PUMP DELIVERY POINTS
G. STARTER SWITCH SAFETY BUTTON

SAFETY DEVICE
A safety device has been incorporated in the design of the hydraulic system to protect the implement if a hidden obstruction is struck. In this event, the sudden impact has the immediate effect of relieving the effective weight of the implement from the tractor rear wheels, which thereby lose traction and the tractor stops with the rear wheels spinning, without damage to the implement. The tractor can be reversed and the implement raised, then the tractor moved forward before lowering the implement at a point beyond the obstruction.


KEY TO ANNOTATION
A. LOWER LINKS
B. CHECK CHAINS
C. CHAIN ANCHORS
D. TOP LINK CONNECTION
E. CONTROL SPRING
F. CIRCULAR GROOVE
G. P.T.O. CAP
H. LEVELLING LEVER
J. UPPER LINK ASSEMBLY

LINKAGE TOP LINK CONNECTION
Do not in any circumstances attempt to pull or tow directly from the top link connection or to alter the setting of the main control spring located behind the driver's seat.

On later tractors, adjustment of the upper link assembly is obtained by locating the centre bolt in different pairs of holes in the two members - by this means, the length can be raised between 24½" (622mm) and 26½" (672mm). The shortest adjustment should only be used with certain implements and, in such cases, a precise recommendation will be made.

LOWER LINKS
Remember when coupling implements to the lower links, always fir the left side first and use the levelling lever to assist in fitting the right side. The check chains prevent the implement from swinging side-ways into the rear wheels. It is particularly important that these chains are not twisted and that the chain anchors are assembled correctly with the chain attached above the centre as shown in Fig 6.

The right-hand lift rod is marked by a circular groove, which, when level with the top of the fork into which it threads, indicates that both lower links are level.

ADJUSTABLE DRAWBAR
Normal setting is 18'' (457mm) between drawbar and ground when the lower links are horizontal and the notches in the stays are in line. the height range is between 10'' (254mm) and 23'' (584mm) above ground.

By raising the drawbar, i.e. shortening the stays, traction is increased with trailed machinery. Lowering the drawbar will tend to keep the front end of the tractor down at the expense of some loss of traction.
The height adjustment is particularly useful when working with trailers with high turntables, e.g. four-wheel horse wagon conversions. By raising the drawbar, strain on the turntable is reduced and the line of draft is improved.


When the drawbar is fitted, as shown above, ensure that the hydraulic control lever is locked in the fully forward position by means of the Safety Stop, as shown below :


and that the pump gear is disengaged when the hydraulic mechanism or power take-off is not being used.

When the drawbar is in continuous use, there is a possibility that the working parts of the hydraulic system may become stiff through lack of use. To avoid this, disconnect the drawbar each day and, by operating the hydraulic control lever, raise and lower the linkage several times.

USE OF BREAKS
The combined brake pedal operates the brakes on both rear wheels. Earlier tractors are fitted with a ratchet for parking and later tractors have a brake parking latch.

When the parking latch lever is set forward, the brake pedal is locked down in the position established by the next pressure of the operator's foot and cannot be released until the lever is moved to the rear. Moving the lever forward does not in itself lock the pedal; it ensures, however, that when next the brakes are applied, they remain ''on''.


The independent brake pedals, which are for assisting reduction of the turning circle and operate the brake on the appropriate when only, should never be applied when travelling at high speed, as this can cause excessive stress.

Always keep the brakes in a good state of adjustment. Unbalanced or slackly adjusted brakes can be dangerous and, if binding, will cause rapid lining wear and excessive fuel consumption.


Keep an eye open for the next episode - OPERATIONAL INSTRUCTIONS for the FERGUSON TE-F 20 Tractor (Vaaljapie)

.

Car of the Month December 2014 is the MG TC/TD/TF

To get back into production quickly after the Second Word War, MG of Abingdon, Oxfordshire, had no option but to warm up its pre-war model, the TB. Thus the TC of 1945 had the same big 19in (48cm) wheels, fold-flat screen, crude semi-elliptic suspension and slab-tank body with ash framing. The body was wider now to give more elbow room for its passengers, while synchromesh on second, third and top gear made it more pleasant to drive. Hydraulic brakes were another welcome improvement.


1949 MG TC

Traditionalists loved it: it was nippy - 78mph (125kph) flat-out - and fun to drive. Nobody seemed to mind the heavy steering and rock-hard suspension. US servicemen stationed in the UK loved them so much they took them home and gave Americans a taste they never lost for European sports cars. Soon the C was spearheading an export drive to the USA - and that's where most of the 10,000-car production run ended up.

Charming as it was, the out-dated TC couldn't go on for ever, so fir 1949 MG introduced the TD: same chassis, same 1250cc four-cylinder engine, but with the new independent front suspension and the rack-and-pinion steering of the YA. Bumpers front and rear and smaller disc wheel didn't do much for the looks, but the TD was roomier and slightly faster, especially in higher compression MKII form from 1952. The TD was a big seller, racking up 29,664 units in its four-year production run.


1954 MG TD

The MG TD MK.II

The final flowering of the traditional MG was the TF of 1953. 

By moulding the headlamps into the front wings, which sloped the grill and fuel tank, Abingdon had gently modernised the shape. Inside, there were individual front seats and a re-styled dashboard. Early cars had the 1250cc engine, but from 1954, a 1500cc unit, giving 63bhp restored some of the performance.

The TF was a holding operation until the MGA appeared The TF looked what it was - warmed-up left-overs - and was really a holding operation while Abingdon prepared its first modern post-war model, the MGA of 1955. Ironically, the TF is the most sought-after of the three "square-rigger" post-war MG's.

MG TC/TD/TF - 1945 - 1955
ENGINE - In-line four
CAPACITY - 1250cc/1466cc
POWER - 54-63bhp
TRANSMISSION - 4-speed manual
TOP SPEED - 78-86mph (125-138kph)
NO. BUILT - 10,000 TC 29,644 TD 9,800 TF

The TD of 1949 was the first MG sports car to have the independent suspension system 

 1954 MG TD - rear

1954 MG TD - grill

1954 MG TD - rear

1954 MG TD - interior

1954 MG TD - interior

1954 MG TD - side view

::

1964 MGB Roadster


Just arrived - 1964 MGB Roadster, very rare pull-handle model, not code 2 or 3, uninterrupted paper trail since 01-01-1965, five 60-spoke painted spoke wheels, new tyres, up-rated 5-main bearing motor plus over-drive. Fitted with new soft top, boot carrier, chrome bumper. Red body, black upholstery with red piping, black mats. Been garaged all it's life, totally original. Needs a bit of TLC. For sale - Contact Dave +27 83 625 4445 or contact me via the CONTACT FORM on the right side of this page.




Out of the blue came this 1964, very rare, pull-handle MGB Roadster from a chap in Port Alfred. After chatting to him, I bought the car over the phone without seeing it. When it arrived, it was true to spec in an unmolested condition. the paper work is unmolested since 01-01-1965, with the last owner having had the car for the past 15 years. After examining the car and taking same for a drive as soon as it arrived, I was amazed at the performance of this almost 60-year-old car, as only the British can produce!




Road-holding is absolutely true to style for a car of the period and a tribute to past motoring.

Engine 1798cc, high compression, aluminium tappet cover and sump, pancake air cleaners, over-drive, twin SU's, modern alternator, 5-main bearing engine




::

1969 Jaguar E-Type 4.2 Series II Coupe


This particular model is Olde English White with Black leather interior, wooden steering wheel and Chrome Wires. This car was found in good nick with its tool-kit, jack, lead hammer and tool for knock-ons.

There has been a huge upswing in the classic and vintage car market recently - prices have sky-rocketed and available stock is becoming more and more scarce. I would imagine a great factor is the fact that a lot of our stock is grabbed up by overseas collectors due to the fact of our vehicles being largely rust free and as the rand weakened and greater prices were realised overseas, many of our cars are being exported.

 One of the greatest of all British sports cars ever to be manufactured (and this fact is supported by the many conversions and build-up kits being offered to the enthusiast), was the Jaguar E-Type - (Roadster in particular, as far as I'm concerned) and it was an instant classic, an exercise in cool, aerodynamic theory and unashamed showmanship, producing probably the most beautiful sports car of the 60's.`

From the outside, the 3.8 and 4.2 Series I E-Types are had to tell apart, but the bucket seats are a giveaway : this one below is a 3.8 roadster.



Below: The Series I and Series II compared - the later car has open headlights to comply with American safety regulations.


It had the ability to live up to it's looks, too. The 150mph (241kph) that Jaguar claimed for the E-Type was devastatingly quick in 1961 (in reality, only the tweaked-up press cars could achieve it, and 140 (225) was nearer the truth), making the new Jaguar Britain's fastest production car. Better still, it was probably Britain's greatest bargain price-wise, undercutting its nearest rival, the Aston Martin DB4, by a third.

That curvy shell, inspired by the Le Mans-winning D-Type racer, was immensely stiff - all the better to take advantage of it s new wishbone and coil-spring independent rear suspension.

Combining near-limousine ride comfort with vice-like grip, even on the slender cross-ply tyres that looked like something off a bike to modern eyes, the new Jaguar handled superbly. Providing the power was the 3.8litre XK engine, already 13 years old but still well worthy of the new chassis.

The same couldn't be said of the elderly, slow-shifting Moss gearbox, a feature of all Jaguars since the 1930's or the disc brakes that were spoilt by an uncertain-feeling pedal.

Pop stars, racing drivers and royalty jostled for position in an ever-lengthening waiting list for the car. Lew Grade wanted to borrow one for his new British TV series, The Saint, but Jaguar turned him down - they could sell every car they could make.

 Despite the demand, development continued. The bigger 4.2 engine from 1964 was torquier and and came with a much better gearbox and brakes. Seats and trim improved, as did the electrics, making the 3,2 Series I E's the best of the bunch. Appeals for a roomier car were met by a two-plus-two version in 1966 and there was even an automatic, as Jaguar tried to reconcile the E's performance image with a need to increase sales in America.

The E-Type's design found a place in the Museum of Modern Art and is sensual rather than sexy, for the car was designed from the heart and the world has been in love with it from the start!

Below : On the open road, the E-Type was good for over 140mph (225kph). The car in front is an early Series I 3.8 Roadster, behind is a Series II Coupe. 



.

1966 Jaguar 3.8 MK.II


About two years ago I heard about a 1966 Jaguar 3.8 MK.II which was for sale in Tzaneen. I phoned the owner and after a short discussion I decided to go and have a look at it. I was astounded at the originality of the car and bought it on the spot. I put in a battery and fuel and even after standing for 20 years, it started immediately and ran like a watch. We drove it onto the truck and headed back to Tarlton.

BEFORE - 1966 Jaguar 3.8 MK.II 

Upon closer inspection at home, I found the original tool kit in the boot in it's original tray situated in the spare wheel well. In the glove box I found the original Jaguar wallet with it's hand-book, Wall Service Chart and the original factory warranty. The licence fees had been paid every year from 1966 by the previous owner. Incredibly, the car has done only 85,000 miles, never been in an accident and the cylinder-head has never been off.

AFTER - 1966 Jaguar 3.8 MK.II

Over the next year or so, I re-sprayed the car Windsor Blue, an original Jaguar colour, cleaned up the upholstery and woodwork and fitted a new set of brake pads as well as new silencers.

The windscreen is original, but I renewed the rubbers when I sprayed the car and also put in new rubbers at the rear window. Mechanically the engine, gearbox, over-drive and suspension is original apart from new rubbers and grease boots. the car went through roadworthy the first time and turns heads whenever I drive it.

C'est la vie – happy motoring!
From the pen of the "Ja Broer" (Dave Clarkson)


More than 80 000 MK.II's were sold and the model inspired a whole raft of more expensive variations on the same theme : The S-Type, the 420 and even a Daimler with its own special V8 engine. It is the pure original MK.II, however, that has won the hearts of enthusiasts and collectors.


The sight of a Jaguar MK.II inspires a misty-eyed emotional response like no other 60's saloon. For a decade from 1959, the year of Britain's first motorway, the compact Jaguar was the bread and butter of Browns Lane, Coventry. It was the last proper sports saloon the company ever made.

The MK.II was nothing if not versatile. It was favoured not just by the criminal fraternity (it was no accident that the James Fox character drove a white MK.II in Donald Campbell's superb 1970 film Performance, or Michael Caine's pursuers a red one in the classic Get Carter of 1971) but also by the law itself, because it was so wickedly fast. At the same time, the MK.II was also a very respectable car; a quiet, comfortable and classy businessman's express for the stockbroker belt. It made a fine name for itself on the track as a saloon-car racer, and industry personalities such as Graham Hill and Colin Chapman gave the MK.II the stamp of approval by using them off-duty too.


Technically, the MK.II wasn't vintage Jaguar (though the unitary shell had broken new ground for the company on its 2.4 MK.I progenitor of 1955), but its beautifully-balanced shape had the classic William Lyons touch, as did the interior with its leather seats and wooden dash and door cappings - the fascia packed with dials and switches like a wartime bomber's flight deck.

The MK.II owner could do a legal 125mph (201kph) if he owned the full-house 3.8 manual overdrive car - it was the fastest saloon on the road for a time in the early 60's - or 120 (193) in the 3.4. The leisurely 2.4, on the other hand, couldn't even mange 100 (160) - which was why Jaguar's press department never allowed one out to be tested.



JAGUAR MK.II - 1959 - 1969
Engine - Straight Six
Capacity - 2483/3442/3781cc
Power - 120-220bhp
Transmission - 4-speed manual, 3-speed auto
Top speed - (3.8) 125mph (201kph)
No. built - 83 980

The 1966 MK.II was one of the last to have big bumpers: slim line bumpers were announced for the 240/340 models of 1967. Jaguar gave the MK.II a bigger rear window and different semi-open spats to help brake cooling.

Above : The 3.8-litre engine gave a claimed 220bhp, making the MK.II one of the fastest saloons on the road. 

"The Cat" 

At the Centenary Car Club, Tarlton, Gauteng, South Africa

At the Centenary Car Club, Tarlton, Gauteng, South Africa 


1966 Jaguar 3.8 MK.II - Car of the Month May 2012 - Centenary Car Club

::